Spent 15 minutes leaving a comment to the guy who posted a pic and the comment disappeared when I pressed the submit icon. I really hate when that happens. I should always write in a text editor and copy/paste comments.
This forum is pretty good about recovery. Some times messages appear gone, but by recomposing it comes back.
It seems like the entire Toshiba A66x lie like to hit control R for a LEFT SHIFT R sometimes. I had both the KB and MB replaced so it has to be systemic,
I was talking about Banggood's site when I mentioned the comment disappearing, not this site.
The rest of your post I do not understand. If not meant for me, that's ok
I plan to cut the display opening larger and not use the extra standoffs. This will allow the display and switch to stick out the front of the case. This will only work without a battery installed since it reduces the space between the PCB and the front of the case where the battery would go.
This appears to be how they did it in the picture on the Banggood website at **broken link removed**
My Laptop seems to have a systemic problem. Other people are complaining too but complaints to Toshiba go to deaf ears.
Every once in a while, by browser gets a ^R instead of a a capital R. ^R means the browser refreshes, hence I loose what I'm composing. If I use the right shift key, there are no problems, Other programs have issues too and it's both Windows and Linux on the same series laptops.
This forum has a way of recovery. Long messages are better composed in an editor. Some websites limit your time. e.g. My bank. The auto-logoff is very short and typing doesn't count. So, if it takes longer than 10 minutes to compose, it's lost. When you try to send you find out you have been logged out without notice.
I believe you are correct, CapeCAD! Good thinking.
For me the battery is the way to go.
The switch must be mounted as high off the board as possible and then no problem.
The leads/legs were already cut on my switch but I was able to raise it just enough that I can get the switch to work but not 'click'. I could also work out a way to raise the extension a little.
If/when I get a new switch I'll replace this one.
"I wound a toroid yesterday that was 6.16uh and it could not measure that small an inductance.
Just measured a choke 861uh (L&C meter) - 0.88mh on the multi-tester.
Here's a clever trick to measure a small inductance.
Place a 1mH inductor on the leads and read the result. Add the inductor you are winding IN SERIES with the 1mH and the result should be just like adding two resistors in series. The result will be slightly more than 1mH.
In this way you can measure very small inductances, much smaller than the minimum shown on the specifications for the tester.
Just to let you know, I've put mine in it's case today - same as flat5, had to cut the protrusions off the bottom of the case, and obviously drill a hole for the switch extension.
I removed the connector strip for the input wires and turned it round, so it made it easier to get the wires in through the holes in the top.
My iteration of the tester, in a box when semiconductors came nicely packaged.
My unit reads al bad (gains ohms) with Rs over 2 Meg. Anyone else have that? E
I finally got 1.11K programmed on a 328p using a Bus Pirate and avrdude software. Adds quite a few updates over the 1.05 version that came with the kit. It also supports other options such as a rotary dial, frequency counter, frequency generator, 10bit PWM, HV zener HW option and more.
If your programmer supports avrdude I managed to stumble through it. I tried using an Arduino UNO as the programmer and it was a mess as it wouldn't program the eeprom. Probably an avrdude setting I didn't understand. I used a Bus Pirate and it went fine but would mess up the fuse settings grr.
It's a good idea to program a new blank ATMega328p, just ignore the fuse settings to start *it'll run too slow but the LCD should work*, then have at the fuses to set the oscillator to 8MHz external.
The rub with AVR programming is almost every hobbyist programmer is the low voltage kind and can't reset the fuses. Going to build an Arduino based HV eraser rig just to reset the fuses.