Unforgiven143
New Member
I included a picture of what I am working on. This is going to be an ammo can boombox.
1st question is:
How would I wire the aviation socket and battery to the 3 position switch then to the amp and other electronics? I want to be able to plug the charger in and charge the battery.
2nd question:
Would I use different wiring to be able to play my boombox when it's plugged in without affecting the battery or would it always be charging?
3rd:
Would I use a different cord for that? One for power and one for charging? Or need a switch with more positions? One for charging and one for playing.
4th:
The charger has 2 cords positive and negative. Can I use a 2 pin aviation socket and solder them (+ to +) (- to -) inside and out.
The picture shows:
2 pin aviation socket
12v 7ah battery
3 position 6 pin switch
Tda7492p amp board
I will be including:
12v car charging
2 usb posts
Volt meter
12 computer fan
(Inside the ammo can)
I put a(+) b(-) c(+) d(-) e(+) f(-),
Would it be:
a/b to socket
c/d to battery
e/f to amp
I don't understand how the power will flow in to the battery and out the other way to give the amp power. Does the charging cable push electricity in one direction.
Sorry if my questions sound stupid. I have been looking all this up for the last few days and my questions only turn into more questions.
For example: I want to add a fuse inside. The battery has a constant output of 1.75a per cell. Does that mean I need to find out how many cells times 1.75 to figure out the constant. Or do they all work together putting out 1.75a. I looked up the battery datasheet and that just let to more questions.
5th question:
What size fuse would I need.
Is the fuse amp needed based off the battery power or the electronics the battery will be powering.
These are all the questions I have been asking myself over the last month. I appreciate any help. The 1st question is the most important.
This is my 1st forum and hope I have done this correctly. Thanks everyone.
1st question is:
How would I wire the aviation socket and battery to the 3 position switch then to the amp and other electronics? I want to be able to plug the charger in and charge the battery.
2nd question:
Would I use different wiring to be able to play my boombox when it's plugged in without affecting the battery or would it always be charging?
3rd:
Would I use a different cord for that? One for power and one for charging? Or need a switch with more positions? One for charging and one for playing.
4th:
The charger has 2 cords positive and negative. Can I use a 2 pin aviation socket and solder them (+ to +) (- to -) inside and out.
The picture shows:
2 pin aviation socket
12v 7ah battery
3 position 6 pin switch
Tda7492p amp board
I will be including:
12v car charging
2 usb posts
Volt meter
12 computer fan
(Inside the ammo can)
I put a(+) b(-) c(+) d(-) e(+) f(-),
Would it be:
a/b to socket
c/d to battery
e/f to amp
I don't understand how the power will flow in to the battery and out the other way to give the amp power. Does the charging cable push electricity in one direction.
Sorry if my questions sound stupid. I have been looking all this up for the last few days and my questions only turn into more questions.
For example: I want to add a fuse inside. The battery has a constant output of 1.75a per cell. Does that mean I need to find out how many cells times 1.75 to figure out the constant. Or do they all work together putting out 1.75a. I looked up the battery datasheet and that just let to more questions.
5th question:
What size fuse would I need.
Is the fuse amp needed based off the battery power or the electronics the battery will be powering.
These are all the questions I have been asking myself over the last month. I appreciate any help. The 1st question is the most important.
This is my 1st forum and hope I have done this correctly. Thanks everyone.