Hi all,
I will start to say sorry if I posted in the wrong sub-forum. Also i would like to tell you right away that i'm a beginner at this so pleas don't be to techinal in terms of explaining
Normally i'm good with airsoft guns gears and such, and a huge problem is that the trigger system gets fried in these weapons, so i wan't to build Solid State switch for this purpose.
What i'm trying to build is this:
https://www.youtube.com/watch?v=0x4eEK9hIBw
It removes the stress on the switch and breaks the motor like this:
https://www.youtube.com/watch?v=L-zCzS0s6Pk
it's breaking the motor (reversing the polarity i think) and from what i have read it's doing so with a pMos
I have made a mockup the best i can showing how i think it should be wired but i'm not sure (googled the last 3-4 days for tut's and info)
I'm using a 7,4 or a 11,1 LiPo Battery depending on the rules of the game.
View attachment 62098
I'm using 2 x RGEF600 polyswitch in parallel hence the trigger time (i know that i need to measure the resistance of both before soldering them together to be sure that they get the same load)
Component list:
https://uk.farnell.com/stmicroelectro...220/dp/9935703
https://uk.farnell.com/international-...0ab/dp/1704508
https://uk.farnell.com/littelfuse/5-0...smc/dp/1869376
https://uk.farnell.com/te-connectivit...-6a/dp/1345950
https://uk.farnell.com/te-connectivit...00r/dp/1751317
https://uk.farnell.com/welwyn/pr5-2k2...ppm/dp/1634058
Hope some friendly soul will help me out since my club is tired of frying our switches and it's a pain to replace them (i'm the guy doing that)
Best regard
- Rasmus
I will start to say sorry if I posted in the wrong sub-forum. Also i would like to tell you right away that i'm a beginner at this so pleas don't be to techinal in terms of explaining
Normally i'm good with airsoft guns gears and such, and a huge problem is that the trigger system gets fried in these weapons, so i wan't to build Solid State switch for this purpose.
What i'm trying to build is this:
https://www.youtube.com/watch?v=0x4eEK9hIBw
It removes the stress on the switch and breaks the motor like this:
https://www.youtube.com/watch?v=L-zCzS0s6Pk
it's breaking the motor (reversing the polarity i think) and from what i have read it's doing so with a pMos
I have made a mockup the best i can showing how i think it should be wired but i'm not sure (googled the last 3-4 days for tut's and info)
I'm using a 7,4 or a 11,1 LiPo Battery depending on the rules of the game.
View attachment 62098
I'm using 2 x RGEF600 polyswitch in parallel hence the trigger time (i know that i need to measure the resistance of both before soldering them together to be sure that they get the same load)
Component list:
https://uk.farnell.com/stmicroelectro...220/dp/9935703
https://uk.farnell.com/international-...0ab/dp/1704508
https://uk.farnell.com/littelfuse/5-0...smc/dp/1869376
https://uk.farnell.com/te-connectivit...-6a/dp/1345950
https://uk.farnell.com/te-connectivit...00r/dp/1751317
https://uk.farnell.com/welwyn/pr5-2k2...ppm/dp/1634058
Hope some friendly soul will help me out since my club is tired of frying our switches and it's a pain to replace them (i'm the guy doing that)
Best regard
- Rasmus