Help regarding msp430f5438

[Neerajneo]

I am making a small project using msp430f5438 micro-controller and a L.C.D interface. But I am little confused how to burn the micro-controller as I am planning to buy a msp430f5438 experiment board but that is too costly for me. If anybody can assist me how to burn my 100 pin msp430f5438. And I am little confused about the experiment board that do it has any pins for interfacing such things or it is just a burner circuit. Please help me

 

[ClydeCrashKop]

From: https://www.olimex.com/Products/MSP430/Starter/MSP430-5438-STK/resources/MSP430-5438STK-REV-B.pdf

BOARD FEATURES
CPU: MSP430F5438 mixed signal microcontroller

LCD NOKIA 3310 black/white 84x48 pixels

JTAG connector

JTAG Power_In and Power_Out jumpers

Two extension connectors

UEXT connector

RS232 driver and connector

Power plug-in jack for 9V DC power supply

Voltage regulator +3.3V – VR1(3.3V)

2 status LEDs

Power on Led

Audio In

Audio Out

SD/MMC mini connector

USB device connector

Reset button

User joystick

PCB: FR-4, 1.5 mm (0,062"), solder mask, silkscreen component print

Dimensions: 100x 98mm ( 3.94x 3.85")


BOARD USE REQUIREMENTS
Cables:
The cable you will need depends on the programmer/debugger you use. If

you use MSP430-JTAG, you will need LPT cable, if you use MSP430-JTAG-TINY or
MSP-JTAG-ISO, you will need 1.8m A-B USB cable, if you use MSP430-JTAG-RF,
you can connect it to the USB port of your computer, or via USB cable type A –
female.
Hardware:
Programmer/Debugger – one of our Programmers – MSP430-JTAG,

MSP430-JTAG-TINY
, MSP430-JTAG-ISO, or MSP430-JTAG-RF.
Software:
MSP430 KickStart software.


It looks like you get a lot for $56.00 **broken link removed**
But you need the $75.40 programmer and software.
**broken link removed**

 

[Neerajneo]

From: https://www.olimex.com/Products/MSP430/Starter/MSP430-5438-STK/resources/MSP430-5438STK-REV-B.pdf

BOARD FEATURES
CPU: MSP430F5438 mixed signal microcontroller

LCD NOKIA 3310 black/white 84x48 pixels

JTAG connector

JTAG Power_In and Power_Out jumpers

Two extension connectors

UEXT connector

RS232 driver and connector

Power plug-in jack for 9V DC power supply

Voltage regulator +3.3V – VR1(3.3V)

2 status LEDs

Power on Led

Audio In

Audio Out

SD/MMC mini connector

USB device connector

Reset button

User joystick

PCB: FR-4, 1.5 mm (0,062"), solder mask, silkscreen component print

Dimensions: 100x 98mm ( 3.94x 3.85")


BOARD USE REQUIREMENTS
Cables:
The cable you will need depends on the programmer/debugger you use. If

you use MSP430-JTAG, you will need LPT cable, if you use MSP430-JTAG-TINY or
MSP-JTAG-ISO, you will need 1.8m A-B USB cable, if you use MSP430-JTAG-RF,
you can connect it to the USB port of your computer, or via USB cable type A –
female.
Hardware:
Programmer/Debugger – one of our Programmers – MSP430-JTAG,

MSP430-JTAG-TINY
, MSP430-JTAG-ISO, or MSP430-JTAG-RF.
Software:
MSP430 KickStart software.


It looks like you get a lot for $56.00 **broken link removed**
But you need the $75.40 programmer and software.
**broken link removed**

From: https://www.olimex.com/Products/MSP430/Starter/MSP430-5438-STK/resources/MSP430-5438STK-REV-B.pdf

BOARD FEATURES
CPU: MSP430F5438 mixed signal microcontroller

LCD NOKIA 3310 black/white 84x48 pixels

JTAG connector

JTAG Power_In and Power_Out jumpers

Two extension connectors

UEXT connector

RS232 driver and connector

Power plug-in jack for 9V DC power supply

Voltage regulator +3.3V – VR1(3.3V)

2 status LEDs

Power on Led

Audio In

Audio Out

SD/MMC mini connector

USB device connector

Reset button

User joystick

PCB: FR-4, 1.5 mm (0,062"), solder mask, silkscreen component print

Dimensions: 100x 98mm ( 3.94x 3.85")


BOARD USE REQUIREMENTS
Cables:
The cable you will need depends on the programmer/debugger you use. If

you use MSP430-JTAG, you will need LPT cable, if you use MSP430-JTAG-TINY or
MSP-JTAG-ISO, you will need 1.8m A-B USB cable, if you use MSP430-JTAG-RF,
you can connect it to the USB port of your computer, or via USB cable type A –
female.
Hardware:
Programmer/Debugger – one of our Programmers – MSP430-JTAG,

MSP430-JTAG-TINY
, MSP430-JTAG-ISO, or MSP430-JTAG-RF.
Software:
MSP430 KickStart software.


It looks like you get a lot for $56.00 **broken link removed**
But you need the $75.40 programmer and software.
**broken link removed**

Thanks for your reply your suggestion really reduced my cost of project. Can you please assist me whether IAR workbench software can be used to burn the micro-controller using USB. And I am little bit confuse that whether it has any pin for LCD and KEYBOARD interface???