hey guys
im trying to build this circuit below. but im using 19 LEDs as apposed to the suggested 12 but the resistor R2 is burning up. The brake light works fine (when R2 is not connected) But the side light circuit does not work. When it is connected. the brake lights stay on continuously at full brightness on my car instead of half power.
can anyone shed any light to this please.
**broken link removed**
ripped from original site:
When SW1 is on, the cluster will illuminate at medium brightness. When brakes are operated, SW2 will be closed and the cluster will shine at maximum brightness.
These two brightness levels of the cluster are obtained by a constant current source drive formed by Q1 and Q2. The two constant current levels are set by R2 and R3 values.
* The cluster can be formed by up to 12 LEDs as shown in the circuit diagram. Common cluster types usually range from 5 to 10 LEDs.
* Using the values shown above, stand-by current was 1mA; SW1 on = 20mA, SW2 on = 60mA.
* Constant output current value can be changed by varying R2 and/or R3.
The formula is: R = 0.6/I (in Amperes).
* Please note that the brake current is obtained by paralleling R2 and R3 values.
* Use high brightness, high efficiency red LED types of suitable size and change R2 and R3 values to suit LED's Absolute Maximum Ratings.
* Any Schottky-barrier type diode can be used in place of the 1N5819: the BAT46 type will be a very good choice.
Parts:
R1______________10K 1/4W Resistor
R2______________33R 1/4W Resistor (See Notes)
R3______________15R 1/4W Resistor (See Notes)
D1___________1N5819 40V 1A Schottky-barrier Diode (See Notes)
D2--D13________LEDs High brightness, high efficiency red types (See Notes)
Q1____________BC557 Transistor
Q2____________BC327 Transistor
SW1____________SPST Tail Light Switch
SW2____________SPST Brake Light Switch
im trying to build this circuit below. but im using 19 LEDs as apposed to the suggested 12 but the resistor R2 is burning up. The brake light works fine (when R2 is not connected) But the side light circuit does not work. When it is connected. the brake lights stay on continuously at full brightness on my car instead of half power.
can anyone shed any light to this please.
**broken link removed**
ripped from original site:
When SW1 is on, the cluster will illuminate at medium brightness. When brakes are operated, SW2 will be closed and the cluster will shine at maximum brightness.
These two brightness levels of the cluster are obtained by a constant current source drive formed by Q1 and Q2. The two constant current levels are set by R2 and R3 values.
* The cluster can be formed by up to 12 LEDs as shown in the circuit diagram. Common cluster types usually range from 5 to 10 LEDs.
* Using the values shown above, stand-by current was 1mA; SW1 on = 20mA, SW2 on = 60mA.
* Constant output current value can be changed by varying R2 and/or R3.
The formula is: R = 0.6/I (in Amperes).
* Please note that the brake current is obtained by paralleling R2 and R3 values.
* Use high brightness, high efficiency red LED types of suitable size and change R2 and R3 values to suit LED's Absolute Maximum Ratings.
* Any Schottky-barrier type diode can be used in place of the 1N5819: the BAT46 type will be a very good choice.
Parts:
R1______________10K 1/4W Resistor
R2______________33R 1/4W Resistor (See Notes)
R3______________15R 1/4W Resistor (See Notes)
D1___________1N5819 40V 1A Schottky-barrier Diode (See Notes)
D2--D13________LEDs High brightness, high efficiency red types (See Notes)
Q1____________BC557 Transistor
Q2____________BC327 Transistor
SW1____________SPST Tail Light Switch
SW2____________SPST Brake Light Switch
Last edited: