1)Just built Arduino compatable RBBB (really bare bones board) using Atmega168, with serial programming adapter/ (TTL-RS232 converter). **broken link removed**
Connected LED between pin 13 and gnd.
(2)Downloaded Arduino-0012 to PC.
(3)Connected power (9v) to RBBB, attached converter/progrmm. adapter between RBBB and serial port, com1, on PC.
(4)Pilot light comes on. pin 13 LED flashes on and off
(5)Booted up Arduino-0012 alpha > SKETCHBOOK > EXAMPLES > DIGITAL > BLINK
(6)Tried uploading to I/O board, but get error: Problem uploading to board . there are two error messages:
The pgm BLINK is NOT being uploaded to RBBB.
Can anyone tell me what those error messages mean?
How can I get this RBBB to upload programs (sketches)?
LED connected to pin 13 flashes, which I'm told is due to the pre-loaded arduino bootloader. (it flashes more frequently than one flash per second as BLINK pgm. calls for)
I'm using windows XP. The RBBB is connected to PC serial port using RS232 cable with 9-pin D connectors. (RBBB to serial programming adapter/ (TTL-RS232 converter thru RS232 cable to pc SERIAL PORT).
I've posted this problem (twice) with an Arduino forum more than 2 days ago, with only one replier who couldn't tell me much and was referred to RBBB seller. Seller has been trying to help, but finally said that I should send it all back to him so he can test the parts. But I think its still has something to do with the inability of PC and microcontroller to recognize each other.
Searching thru the internet, I've found several other postings by people who have had the same problems with Arduino equipment, but have been unable to come up with any answers as to how to fix the problem. Nobody seems to know what to do, or what those error messages mean.
Thanks
Patrick
Connected LED between pin 13 and gnd.
(2)Downloaded Arduino-0012 to PC.
(3)Connected power (9v) to RBBB, attached converter/progrmm. adapter between RBBB and serial port, com1, on PC.
(4)Pilot light comes on. pin 13 LED flashes on and off
(5)Booted up Arduino-0012 alpha > SKETCHBOOK > EXAMPLES > DIGITAL > BLINK
(6)Tried uploading to I/O board, but get error: Problem uploading to board . there are two error messages:
(i) avrdude: stk500_get sync(): not in sync: resp+0x00
(ii)avrdude: stk500_disable(): protocol error, expect=0x14, resp=0x51
(ii)avrdude: stk500_disable(): protocol error, expect=0x14, resp=0x51
The pgm BLINK is NOT being uploaded to RBBB.
Can anyone tell me what those error messages mean?
How can I get this RBBB to upload programs (sketches)?
LED connected to pin 13 flashes, which I'm told is due to the pre-loaded arduino bootloader. (it flashes more frequently than one flash per second as BLINK pgm. calls for)
I'm using windows XP. The RBBB is connected to PC serial port using RS232 cable with 9-pin D connectors. (RBBB to serial programming adapter/ (TTL-RS232 converter thru RS232 cable to pc SERIAL PORT).
I've posted this problem (twice) with an Arduino forum more than 2 days ago, with only one replier who couldn't tell me much and was referred to RBBB seller. Seller has been trying to help, but finally said that I should send it all back to him so he can test the parts. But I think its still has something to do with the inability of PC and microcontroller to recognize each other.
Searching thru the internet, I've found several other postings by people who have had the same problems with Arduino equipment, but have been unable to come up with any answers as to how to fix the problem. Nobody seems to know what to do, or what those error messages mean.
Thanks
Patrick