How to send conversion axis command to acclerometer thru SPI interface to PIC18f452

#include<18f452.h>
#use delay (clock=6000000)
#use rs232 ( baud= 9600, xmit=PIN_C6, rcv= PIN_C7 )
#include<input.c>
#include<spi.c>
//#include<ACCL.h>
VOID main()
{
unsigned int a,b,FF_int=0x06, FF_delay=0x07, MOT_int=0x08, MOT_delay=0x09
                 XOUT_H, XOUT_L, YOUT_H, YOUT_L, ZOUT_H, ZOUT_L;
unsigned char spi_write, spi_read;
                          //spi_write(0x06 && 0x14)
spi_write(FF_int);
spi_write(0x14);
delay_us(130000);
                           //spi_write(0x07 && 0x14)
spi_write(FF_delay);
spi_write(0x14);
delay_us(130000);
                           //spi_write(0x08 && 0x4d)
spi_write(MOT_int);
spi_write(0x4d);
delay_us(130000);
                           //spi_write(0x09 && 0x14)
spi_write(MOT_delay);
spi_write(0x14);
delay_us(130000);
                           //void spi_io(void);
{
setup_spi(spi_master, spi_slave)

CS=0                           //chip slect low to write to registers
                               //a=0x8b
spi_write(0x0b);               // intiates write to control regb
spi_write(0x06);               // write operational mode byte to control regb
                               //spi_write(0x0b && 0x06)
   CS=1;
   delay_us(130000);
   CS=0;
spi_read(0x8b);
a=spi_read(0x06);                  //intiates the read from control reg b
   CS=1;
   delay_us(130000);
   CS=0;
                                // b=0x8a
spi_write(0x0a);                // intiates write to control regc
spi_write(0x00);                //write operational mode byte to control regc
                                //spi_write(0x0a && 0x00)
    CS=1;
    delay_us(130000);
    CS=0;
spi_read(0x8a);
b=spi_read(0x00);                //intiates the read from control reg c
CS=1;
delay_us(130000);              //chip select high before the next data request
CS=0;

                              //  conversion command
spi_write(0x80);
SCLK=0;
delay_us(200);
XOUT_H=spi_read(0x80);
XOUT_L=spi_read(0x81);
CS=1;
delay_us(130000);
CS=0;
spi_write(0x82);
SCLK=0;
delay_us(200);
YOUT_H=spi_read(0x82);
YOUT_L=spi_read(0x83);
CS=1;
delay_us(130000);
CS=0;
spi_write(0x84);
SCLK=0;
delay_us(200);
ZOUT_H=spi_read(0x84);
ZOUT_L=spi_read(0x85)
CS=1;
delay_us(130000);

}
}

[code/]


Pleas frens this is my first C program for PIC using SPI so give suggesions where I went wrong.

Thanks in advance