Electro Tech is an online community (with over 170,000 members) who enjoy talking about and building electronic circuits, projects and gadgets. To participate you need to register. Registration is free. Click here to register now.
Welcome to our site! Electro Tech is an online community (with over 170,000 members) who enjoy talking about and building electronic circuits, projects and gadgets. To participate you need to register. Registration is free. Click here to register now.
:o
Hi everybody.
I am using a 6mm pager motor to turn the pulleys on a 1/25th scale model motor. When you pull the carburetor linkage back the motor will start and increase in speed depending on how far you pull the throttle or push the little gas pedal.
The motor is rated at
Starting...
Hi Charliemopps,
You save yourself allot of trouble by going to JC Whitney for all Auto parts - Car, Truck, Jeep, Motorcycle & RV Parts They have all kinds of stuff for power windows and most of it is universal. Another place is YearOne, Inc. they deal with automotive reproduction restoration...
Sorry about that dknguyen I should have highlighted it. It does get a little lost in the typing. The last sections came from the Stansberry Report On line - posted 4/20/2006 .
My apologies.
Also just a note I did check it out on snopes. I just posted this to get peoples input on it. I for...
I coppied this off the website You can go their and read it yourselves or read all the follow up articles about it.
I myself would like to find out allot more about this.
GOOGLE it or follow this link. It will blow your mind.
USGS Release: 3 to 4.3 Billion Barrels of Technically...
I still need help BUT JUST A LITTLE MORE
MrAl
I sent you a PM a few minutes ago.
The answer to your first question is I don't want them blinking like a strobe. I have seen the one second on and 1/2 second off and that looked really good to me. So if you can I would prefer that.
The...
Hi MrAl
I figure if I cover the backside of the board with .005" thick styrene I can use it as the part of the floor in place of the one that came with the kit. so I can give up another .070".
Will that be enough? .170 height max and that is squeezing it. SMD's are pretty easy for me compared...
FANTASTIC MrAl,
it will take me a couple of days to set it up and test it out on a breadboard then I'll build up the SMD circuit. Thank You Mr Al if you need any of my extra stuff let me know and I'll ship it to you. Bye the way What do I owe you for all your time and knowledge?
Hi MrAl again we speak (type)
Thank yo so much I'd like to stay with the first schematic and not change the blink rate. Maybe I'll try it on a different board down the road sometime. Could I bother you to just sketch a the yellow light where it ties into the 3 red Led's. I have short term...
Hi Boncuk
thank you for the motor controller The motor is a micro pager motor and is rated at 1.5 volt max.
The button type batteries I am using are Sony and I buy them for $3.50 a dozen. My 1.5 volt batteries I paid $2.00 for 15 and yes they are current batteries. I buy them from a...
Hi Again MrAl,
These drawings look great but I still have to wire in the 2 front yellow Led's one on each side. Where would I tie them in at.
I can't believe all the help you have given me so far
you are a Fantastic person
Thank You
MrAl
So far it looks good. I know it is just a rough drawing but I will need the pin layout for the SA555's and a Key to the parts. Like I say I'm dumber than than Dumb can be when it comes to reading a schematic. I can understand most of what you have so far but d1 &d2 placement is still...
Hi Again MrAl
The actual part numbers are SA555 By T.I. and I have 10 of them. the resistors I have 20 each and the capacitors I have 5 each. Getting more parts with higher values is easy I only pay $1.00 for 20 resistors and the SA555's are only .49 cents each. I know I will need some diodes...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.
