DIY Solderstop mask - Electronic Circuits Projects Diagrams Free

Boncuk · 2nd November 2009, 03:04 AM

Hi all,

I found an interesting film about DIY solderstop mask. All texts are German.

If translation is needed I will provide the English text for each text page in the film.

Required material for the solderstop mask:

- High power (450W) laminator
- Dynamask Laminate
- negative developer (Natriumcarbonate, 10g/l at 40deg/C)
- UV exposure box
- soft brush to expedite developing (toothbrush or similar)

There are direct links to the material required in the article.

Here is the link: http://www.gerold-online.de/cms/uc-p...stopplack.html

Greetings

Boncuk

DirtyLude · 2nd November 2009, 03:25 AM

That is really pretty good. Impressed with the outcome.

günter · 2nd November 2009, 07:26 PM

Hello Boncuk,

>"If translation is needed I will provide the English text for each text page in the film"

can i have the translation of my homepage too?

sorry, im good in making soldermasks, but not in translating ;-)

Günter

Boncuk · 3rd November 2009, 12:24 AM

Hello Günter,

hopefully you have a contact address on your homepage. If not please contact me via email.

Of course I'll be glad to help you.
Remark: Next time you make a movie get the microphone away from the adhesive tape roller.

When unreeling the tape and tearing it off it sounded like a lightning strike on my home theater.

Email address is posted in a PM to you.

Regards

Hans

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar
Title	Starter	Forum	Replies	Latest
Hand Applied Solder Mask	Noggin	General Electronics Chat	8	19th December 2007 04:14 PM
How to apply a filters and mask ond CAN Bus controller MCP2515	rafaelvg	Micro Controllers	10	16th August 2007 05:11 PM
How do to a mask using CCS on PIC?	boncker	Micro Controllers	1	9th December 2006 07:17 PM
8085: Set Interrupt Mask.	lord loh.	General Electronics Chat	0	22nd January 2006 02:52 PM
Solder Mask	CoTang	General Electronics Chat	4	21st January 2004 12:40 AM

2nd November 2009, 03:04 AM	#1
Boncuk	DIY Solderstop mask Hi all, I found an interesting film about DIY solderstop mask. All texts are German. If translation is needed I will provide the English text for each text page in the film. Required material for the solderstop mask: - High power (450W) laminator - Dynamask Laminate - negative developer (Natriumcarbonate, 10g/l at 40deg/C) - UV exposure box - soft brush to expedite developing (toothbrush or similar) There are direct links to the material required in the article. Here is the link: http://www.gerold-online.de/cms/uc-p...stopplack.html Greetings Boncuk __________________ Proper Planning Prevents Piss Poor Performance Last edited by Boncuk; 2nd November 2009 at 03:06 AM.

2nd November 2009, 03:25 AM	#2
DirtyLude	That is really pretty good. Impressed with the outcome. __________________ Mark Higgins

2nd November 2009, 07:26 PM	#3
günter	Hello Boncuk, >"If translation is needed I will provide the English text for each text page in the film" can i have the translation of my homepage too? sorry, im good in making soldermasks, but not in translating ;-) Günter

3rd November 2009, 12:24 AM	#4
Boncuk	Hello Günter, hopefully you have a contact address on your homepage. If not please contact me via email. Of course I'll be glad to help you. Remark: Next time you make a movie get the microphone away from the adhesive tape roller. When unreeling the tape and tearing it off it sounded like a lightning strike on my home theater. Email address is posted in a PM to you. Regards Hans __________________ Proper Planning Prevents Piss Poor Performance