I need help with a Signal Sending Circut - Electronic Circuits Projects Diagrams Free

ghost309 · 15th May 2008, 04:17 AM

I have the BASIC stamp homework board by parallax. I also have their PIR sensor. I want to make the circut so it will send a signal to my phone without another phone, but rather the computer. The only problem is, I don't know how to make something like that. So, does anyone know what i could do? This is the code I am using right now:

' ================================================== =======================
'
' File...... PIR_Advanced_Demo.bs2
' Purpose... Demonstrate PIR Sensor With Warm-Up Code
' Author.... Parallax, Inc.
' E-mail.... support@parallax.com
' Started... 12-14-2005
'
' {$STAMP BS2}
' {$PBASIC 2.5}
'
' ================================================== =======================

' -----[ Program Description ]---------------------------------------------

' This PIR demo allows you to see how to go about allowing a warm-up time
' for the sensor to settle, as well as displayed number of times tripped
' and possibly activating an alarm or relay, in this case the LED. The LED
' should have a 220 ohm or 330 ohm resistor in series with it.

' -----[ I/O Definitions ]-------------------------------------------------

PIR PIN 0 ' I/O Pin For PIR Sensor
LED PIN 1 ' I/O Pin For LED

' -----[ Variables ]-------------------------------------------------------

counter VAR Byte ' Trip Counter

' -----[ Initialization ]--------------------------------------------------

DEBUG CLS ' Clear DEBUG Screen
FOR counter = 40 TO 0 ' Wait 40 Seconds For PIR Warm-Up
DEBUG HOME, "WARMING UP:", DEC2 counter
PAUSE 1000 ' Display Counter Every Second
NEXT

counter = 0 ' Clear Counter Variable

DEBUG HOME, "WAITING... " ' Display Waiting Message

' -----[ Program Code ]----------------------------------------------------

Main:
DO
IF PIR = 1 THEN ' Motion Detected?
counter = counter + 1 ' Update Trip Counter
HIGH LED ' Light LED
DEBUG HOME, "TRIPPED...", DEC3 counter
DO : LOOP UNTIL PIR = 0 ' Wait For PIR To Clear
DEBUG HOME, "CLEARED...", DEC3 counter
LOW LED ' Turn Off LED
ENDIF
LOOP

PLEASE HELP!

Gayan Soyza · 15th May 2008, 06:22 AM

I don't use this micros but I need some details.Do you need to ring the phone (Land phone) after PIR detects a signal?

ghost309 · 15th May 2008, 02:37 PM

Actually, I want a signal sent to my Cell phone. Just a simple text saying something like Intruder. I wasn't going to use a land line because I want to know if anybody goes into my room while im not home.

blueroomelectronics · 15th May 2008, 03:32 PM

How do you plan on connecting the Stamp to your cell phone?

ghost309 · 15th May 2008, 11:31 PM

Well, I dont want to connect it to the cell phone. Rather, I want to send some kind of signal to the computer to send me a text to my phone. Yes, I know it's complicated, but I don't have the money to buy another cell phone. Anyways, yeah. I want a signal sent to my computer to get it to send me a text. Bottom line. I know Yahoo lets you send texts, but I don't know how I would go about it. Am I going to need a special program for it, or could I make something?

15th May 2008, 04:17 AM	(permalink)
ghost309 New Member	I need help with a Signal Sending Circut I have the BASIC stamp homework board by parallax. I also have their PIR sensor. I want to make the circut so it will send a signal to my phone without another phone, but rather the computer. The only problem is, I don't know how to make something like that. So, does anyone know what i could do? This is the code I am using right now: ' ================================================== ======================= ' ' File...... PIR_Advanced_Demo.bs2 ' Purpose... Demonstrate PIR Sensor With Warm-Up Code ' Author.... Parallax, Inc. ' E-mail.... support@parallax.com ' Started... 12-14-2005 ' ' {$STAMP BS2} ' {$PBASIC 2.5} ' ' ================================================== ======================= ' -----[ Program Description ]--------------------------------------------- ' This PIR demo allows you to see how to go about allowing a warm-up time ' for the sensor to settle, as well as displayed number of times tripped ' and possibly activating an alarm or relay, in this case the LED. The LED ' should have a 220 ohm or 330 ohm resistor in series with it. ' -----[ I/O Definitions ]------------------------------------------------- PIR PIN 0 ' I/O Pin For PIR Sensor LED PIN 1 ' I/O Pin For LED ' -----[ Variables ]------------------------------------------------------- counter VAR Byte ' Trip Counter ' -----[ Initialization ]-------------------------------------------------- DEBUG CLS ' Clear DEBUG Screen FOR counter = 40 TO 0 ' Wait 40 Seconds For PIR Warm-Up DEBUG HOME, "WARMING UP:", DEC2 counter PAUSE 1000 ' Display Counter Every Second NEXT counter = 0 ' Clear Counter Variable DEBUG HOME, "WAITING... " ' Display Waiting Message ' -----[ Program Code ]---------------------------------------------------- Main: DO IF PIR = 1 THEN ' Motion Detected? counter = counter + 1 ' Update Trip Counter HIGH LED ' Light LED DEBUG HOME, "TRIPPED...", DEC3 counter DO : LOOP UNTIL PIR = 0 ' Wait For PIR To Clear DEBUG HOME, "CLEARED...", DEC3 counter LOW LED ' Turn Off LED ENDIF LOOP PLEASE HELP!

15th May 2008, 06:22 AM	(permalink)
Gayan Soyza Experienced Member Blog Entries: 1	I don't use this micros but I need some details.Do you need to ring the phone (Land phone) after PIR detects a signal? __________________ Gayan Forum Supporter

15th May 2008, 03:32 PM	(permalink)
blueroomelectronics Experienced Member Blog Entries: 4	How do you plan on connecting the Stamp to your cell phone? __________________ Bill Smart Kits build Smart People http://www.blueroomelectronics.com

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Latest
The Oscilloscope	ElectroMaster	Electronic Theory	12	3rd February 2008 01:45 PM
Using Oscilloscopes	mechie	Electronic Theory	9	29th November 2007 09:48 PM
Enquiry For some signal questions	shermaine	Electronic Theory	6	5th December 2006 06:02 AM
Anybody got information on line driving a c-sync signal?	FusionITR	General Electronics Chat	8	15th April 2006 04:16 PM
Yet another LED taillight controller......	NickK	Electronic Projects Design/Ideas/Reviews	1	31st March 2003 05:37 PM

15th May 2008, 02:37 PM	(permalink)
ghost309 New Member	Actually, I want a signal sent to my Cell phone. Just a simple text saying something like Intruder. I wasn't going to use a land line because I want to know if anybody goes into my room while im not home.

15th May 2008, 11:31 PM	(permalink)
ghost309 New Member	Well, I dont want to connect it to the cell phone. Rather, I want to send some kind of signal to the computer to send me a text to my phone. Yes, I know it's complicated, but I don't have the money to buy another cell phone. Anyways, yeah. I want a signal sent to my computer to get it to send me a text. Bottom line. I know Yahoo lets you send texts, but I don't know how I would go about it. Am I going to need a special program for it, or could I make something?