Electronic Projects, forums and more.

Go Back   Electronic Circuits Projects Diagrams Free > Electronics Forums > General Electronics Chat


General Electronics Chat This forum is for general chat about electronics, eg: Dont know what a part does? Dont know how to read a circuit? Want to get an opinion?

Reply
 
LinkBack Thread Tools Display Modes
Old 5th January 2008, 11:38 PM   (permalink)
Default Amber & White Using RGB LEDs

I need a little help again about RGB LEDs. I was wondering is it possible to make amber and white colors using RGB LEDs. They seem to make RGBA leds, but seems hard to find them. I need Red, Blue, Amber, and White dies in one led if possible.

Shane
madcitysw is offline  
Old 6th January 2008, 12:39 AM   (permalink)
Default

The whole point of an RGB LED is you can change the colour.

For white, turn the red, green and blue dies on at the same time.

For amber you want the red and green dies on but slightly more current thought the red so calculate the series resistor value to give more current.
__________________
I also post at the following sites:
http://www.stop-microsoft.org http://www.heated-debates.com
Screen name: Aloone_Jonez
Hero999 is offline  
Old 6th January 2008, 01:32 AM   (permalink)
Default

As Hero pointed out, you should be able to make any color just by varying the currents though the Red Green and Blue LEDs independently. Red Green and Blue are called primary colors and you can make any color by mixing these light sources in different combinations of intensity. Hence RGB monitors, etc
__________________
--- The days of the digital watch are numbered. ---
kchriste is offline  
Old 6th January 2008, 01:58 AM   (permalink)
Default

for a nice white, you want an RGB led that has two green chips in it... or you'll want to use some sort of controller to reduce the red and blue intensities. just turning a regular cheapo rgb led on full blast usually gets you something of a pinkish color.
__________________
If you don't have a planet, what good are gold bars?

want to contact me directly? gmail gordonthree
check out my project website: http://projects.dimension-x.net
Favorite numbers:
09 F9 11 02 9D 74 E3 5B D8 41 56 C5 63 56 88 C0
justDIY is offline  
Old 6th January 2008, 03:50 AM   (permalink)
Default

For amber, run the red die at 100% brightness, green at 80%, and blue at 0%. Raising the green results in yellow and lowering produce orange and finally red.
__________________
The most-hated young engineer in America.
* AVR Projects
* Robot War: TI
* About
DigiTan is offline  
Old 6th January 2008, 04:12 AM   (permalink)
Default

Thanks guys, is there anyway I could control the brightness via a AVR? I guessing you would need to use a PWM, in that case I don't know how to program it to do that. How can I control 12 LEDs at a different time?
madcitysw is offline  
Old 6th January 2008, 04:25 AM   (permalink)
Default

Just Google for avr rgb led and you'll find quite a few projects.
__________________
--- The days of the digital watch are numbered. ---
kchriste is offline  
Reply

Bookmarks

Thread Tools
Display Modes



Similar Threads
Title Starter Forum Replies Latest
White LEDs Driven By Mains ParkingLotLust Electronic Projects Design/Ideas/Reviews 17 23rd July 2007 05:42 AM
Introduction to High Brightness LEDs and Thermal Management Ocelaris Electronic Projects Design/Ideas/Reviews 3 17th March 2007 06:35 AM
Problems with Dual Brightness (Current) LED Tail Lights? Eagle Schematics! Ocelaris Electronic Projects Design/Ideas/Reviews 12 31st December 2006 07:18 PM
[b]Controlling the brightness of two white LED's[/b] lionking83george Electronic Projects Design/Ideas/Reviews 4 22nd March 2004 12:19 PM
LEDs-Super Bright White LEDs $1.35USD ea ssullivan777 Datasheet/Parts Requests 0 27th February 2003 03:02 AM



All times are GMT. The time now is 12:40 PM.


Electronic Circuits  |  Learning Electronics
Powered by vBulletin® Version 3.7.0
Copyright ©2000 - 2008, Jelsoft Enterprises Ltd.

eXTReMe Tracker