I need a stepper motor driver! - Electronic Circuits Projects Diagrams Free

tj107us · 4th February 2006, 10:38 PM

Does any one have or can get a schematic drawing for a stepper motor driver? The stepper motor im going to use in a Sanyo Cp-043 14.5 volts. If i could get a schematic drawing that will make it go forword and backword and make it able to position itself using a computer. The stepper motor has six wires.

thanks in advance,
Jacob

moody07747 · 5th February 2006, 05:06 AM

only stepper motor controller i know of uses 4 wires and its here

http://www.aaroncake.net/circuits/stepper.htm

dont know if you could change that around

**Nigel Goodwin** · 5th February 2006, 11:26 AM

Quote:

Originally Posted by moody07747

only stepper motor controller i know of uses 4 wires and its here

http://www.aaroncake.net/circuits/stepper.htm

dont know if you could change that around

The diagram in the link has SIX wires, two are the power inputs, and four are the connections to the driver - it's a standard unipolar circuit.

If you google for "stepper motor tutorial" you will find plenty of information on steppers and how to run them.

fsahmed · 5th February 2006, 11:40 AM

Try searching for UCN 5804

tj107us · 9th February 2006, 03:17 AM

what is a UCN 5804?

fsahmed · 9th February 2006, 11:50 AM

UCN 5804 is a stepper motor driver IC, takes TTL level input, can run steppers upto 30 volts, 1.25A continuous current

tj107us · 9th February 2006, 10:44 PM

what does it look like and how can i get it?

**Nigel Goodwin** · 9th February 2006, 11:23 PM

Quote:

Originally Posted by tj107us

what does it look like and how can i get it?

If you had you location filled in perhaps we could make suggestions where you could get them?.

tj107us · 9th February 2006, 11:43 PM

its there now

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

4th February 2006, 10:38 PM	(permalink)
tj107us	I need a stepper motor driver! Does any one have or can get a schematic drawing for a stepper motor driver? The stepper motor im going to use in a Sanyo Cp-043 14.5 volts. If i could get a schematic drawing that will make it go forword and backword and make it able to position itself using a computer. The stepper motor has six wires. thanks in advance, Jacob

5th February 2006, 05:06 AM	(permalink)
moody07747	only stepper motor controller i know of uses 4 wires and its here http://www.aaroncake.net/circuits/stepper.htm dont know if you could change that around __________________ Dave www.myspace.com/sonicorbstudios Welcome to "Sonic Orb Studios"

5th February 2006, 11:40 AM	(permalink)
fsahmed	Try searching for UCN 5804 __________________ F. S. Ahmed

9th February 2006, 03:17 AM	(permalink)
tj107us	what is a UCN 5804?

9th February 2006, 11:50 AM	(permalink)
fsahmed	UCN 5804 is a stepper motor driver IC, takes TTL level input, can run steppers upto 30 volts, 1.25A continuous current __________________ F. S. Ahmed

9th February 2006, 10:44 PM	(permalink)
tj107us	what does it look like and how can i get it?

9th February 2006, 11:43 PM	(permalink)
tj107us	its there now