Amplifier with adjustiable output impedence - Electronic Circuits Projects Diagrams Free

drahte1905 · 7th January 2008, 08:53 PM

Design an amplifier that has adjustable output impedance and the range of impedance should be 1K<ri<10K. Voltage gain of the amplifier should be set to 5.

Use an Operational Amplifier, a JFET or a BJT and peripheral passive components to realize the Project.

-----------------------------------------------

I have got several concepts in my mind but when I simulate them they all failed

And I can't find a way to build this kind of a circuit

Any of you know a concept about this circuit

It is a midterm project and has got due date at 09.01.08 so I am in a little bit a rush

on1aag · 7th January 2008, 09:05 PM

Hi lazy devil,

Do you really think we will do all your homework ?
However, look at this circuit:

http://www.electro-tech-online.com/e...d-student.html

The amplifier has a non-inverting gain of 3,2.

on1aag.

drahte1905 · 7th January 2008, 09:16 PM

Thanks for reply

But I have stuck with these projects and my finals are too close also these are maybe 2 of 14 projects

I can't have exact answers to my questions this is why I am writing here

I really put considerable effort on these projects, I didn't ask for pre-made projects, I am just asking for help

It is easier to help rather than just talking...

kchriste · 8th January 2008, 05:27 AM

Maybe a pot in series with the output to vary the impedance?

drahte1905 · 8th January 2008, 04:28 PM

I constracted a circuit but not simulated tomarrow I will simulate and also constract it in labratory

It is very basic non-inverting amplifier with gain for this I will use 100k and 400k as Rf and Rk so my gain gone be 5

Following I will connect 10K at one branch and parllel to this branch a pot [vary between 10k-200k] + 900ohm resistor

So when pot is off or r=0 then 1 have 0.9K ohm output resistance and when pot reach 200K ohm I will have 9.8Kohm also when pot 110K ohm I will have 9.1K[not remember exactly]

Any way I planning to simulate this circuit in following hours I will post a diagram and outputs...

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Title	Starter	Forum	Replies	Latest
Amplifier offset	Zane83	Electronic Projects Design/Ideas/Reviews	8	6th November 2006 07:41 PM
Audio amplifier	tony-ellis	Electronic Projects Design/Ideas/Reviews	7	18th October 2006 08:52 PM
Discrete Pulse width Modulator...	Rajagopal87	General Electronics Chat	8	16th August 2006 06:25 AM
Low Power Audio Amplifier	indecided	Electronic Projects Design/Ideas/Reviews	33	8th May 2005 04:18 PM
Input and Output Resistance Help	andy257	General Electronics Chat	1	21st April 2004 02:35 PM

7th January 2008, 08:53 PM	(permalink)
drahte1905	Amplifier with adjustiable output impedence Design an amplifier that has adjustable output impedance and the range of impedance should be 1K<ri<10K. Voltage gain of the amplifier should be set to 5. Use an Operational Amplifier, a JFET or a BJT and peripheral passive components to realize the Project. ----------------------------------------------- I have got several concepts in my mind but when I simulate them they all failed And I can't find a way to build this kind of a circuit Any of you know a concept about this circuit It is a midterm project and has got due date at 09.01.08 so I am in a little bit a rush

7th January 2008, 09:05 PM	(permalink)
on1aag	Hi lazy devil, Do you really think we will do all your homework ? However, look at this circuit: http://www.electro-tech-online.com/e...d-student.html The amplifier has a non-inverting gain of 3,2. on1aag.

7th January 2008, 09:16 PM	(permalink)
drahte1905	Thanks for reply But I have stuck with these projects and my finals are too close also these are maybe 2 of 14 projects I can't have exact answers to my questions this is why I am writing here I really put considerable effort on these projects, I didn't ask for pre-made projects, I am just asking for help It is easier to help rather than just talking...

8th January 2008, 05:27 AM	(permalink)
kchriste	Maybe a pot in series with the output to vary the impedance? __________________ --- The days of the digital watch are numbered. ---

8th January 2008, 04:28 PM	(permalink)
drahte1905	I constracted a circuit but not simulated tomarrow I will simulate and also constract it in labratory It is very basic non-inverting amplifier with gain for this I will use 100k and 400k as Rf and Rk so my gain gone be 5 Following I will connect 10K at one branch and parllel to this branch a pot [vary between 10k-200k] + 900ohm resistor So when pot is off or r=0 then 1 have 0.9K ohm output resistance and when pot reach 200K ohm I will have 9.8Kohm also when pot 110K ohm I will have 9.1K[not remember exactly] Any way I planning to simulate this circuit in following hours I will post a diagram and outputs...